Feed on
Posts
Comments

This is the first article in a series that I call ‘Learning Electronics’. The goal is to learn and experiment with basic electronic circuits. The first circuit I will discuss here is the astable multivibrator. This is a very simple oscillator circuit that can be used to generate square waves. Here is the schematic of a standard astable multivibrator:

It consists of only two NPN transistors (T1 and T2), two capacitors (C1 and C2), and four resistors (R1-R4), organized in a symmetric fashion. The collectors of T1 and T2 are outputs, which provide complement square wave signals. The values of the capacitors and resistors can vary depend on the desired frequency, and their values do not have to be symmetric.

Update: as some readers pointed out, for square wave output, the resistor values should satisfy: R2 / R1 < h_fe, where h_fe is the transistor's current gain (same for R3 and R4). As h_fe is usually around 80 to 250 for 2N3904, the specific values above (R1=1K, R2=100K) are close to the margin. To improve this, consider increasing R1 or decreasing R2. Alternatively, you can replace 2N3904 with BC547, or even a Darlington transistor (e.g. MPSA14), which have higher h_fe values.

Principles

So how does the circuit work? To begin, when power is applied, theoretically both T1 and T2 should turn on, since their base pins are connected through resistors (R2 and R3) to Vcc. However, due to small differences in the electric properties, one of the them will turn on slightly earlier than the other. Without loss of generality, let’s assume T2 turns on first. Therefore, T2’s collector begins to conduct and can be thought of as ‘shorted’ to ground. Note that C2’s right lead is connected to T2’s collector, and since C2 is not charged yet, its left lead also has a voltage close to ground. This immediately shuts off T1, i.e. T1 becomes an open circuit. Therefore C1’s left lead is in floating status, and its right lead is connected to T2’s base, which is about 0.7V due to the forward voltage drop of transistors. This forward voltage drop is the same as a diode. So at this moment, the circuit is equivalent to the following:

Stage 1

During this period, T2’s collector (output O2) remains low, and C2 begins to charge through R3. Thus the voltage on C2’s left lead will rise, and the rising time depends on R3 x C2. At the same time, C1 also charges, through R1, which is typically a small resistor (e.g. 100-1000 ohm). So C1’s left lead (output O1) will quickly rise up to Vcc and remains high.

As C2 continues to charge, a critical moment will happen when its left lead rise up to 0.7V, at which moment transistor T1 will turn on, and its collector will conduct to ground. Note that since C1’s left lead is connected to T1’s collector, it will also drop to ground voltage. As C1 is fully charged, it’s right lead will suddenly drop to a negative voltage (-Vcc). This will shuts off T2 firmly. Therefore the circuit will suddenly transition to the following equivalent:

Stage 2

During this period, output O1 will remain low, and output O2 will quickly rise to Vcc (due to the charging of C2 through a small resistor R4). At the same time, C1 charges through R2 and the voltage on its right lead will rise over time determined by R2 x C1. Now you can predict what’s going to happen: as C1 continues to charge, the next critical moment happens when C1’s right lead rises above 0.7V. At that point, T2 will conduct again while T1 shuts off. The same cycle will repeat. There you go, oscillators!

Analysis

Now we have to do some calculus to find out the frequency of the oscillator. Let me focus on output O2. As it alternates between low and high, it approximates a square wave. How to find out the frequency? Note at the end of stage 1, C1 has a voltage of (Vcc – Vb) across it (where Vb = 0.7V). Again, the voltage establishes very quickly because R1 is small. The moment the circuit transitions from stage 1 to stage 2, C1’s right lead has an initial negative voltage: -(Vcc – Vb), and the circuit remains in this stage until that lead rises up to +Vb. So let’s calculate how long this will take. There are ready-made equations to compute this, but here let me derive it from basic differential equations.

To start, the problem can be simply stated as follows: a resistor R2 and capacitor C1 are connected in series between Vcc and ground. C1 has an initial voltage of -(Vcc – Vb). How long does it take for C1’s voltage to rise up to +Vb? Let’s assume C1’s voltage is V(t): a function that changes over time. According to the law of capacitor, the change of V(t) is equal to the current flowing through it divided by the capacitance:

How much is the current i(t)? That’s equal to the current flowing through the resistor R2, thus

putting them together:

This is a simple differential equation. We can rearrange it to the following form:

By using the fact that

and integrate both sides, we get:

where K is a constant. Using the knowledge that when t=0, V(t)= -(Vcc – Vb), we find out

so:

Recall that our goal is to find hen V(t) is equal to Vb, so substitute Vb to V(t), and solve for t:

Under the assumption that Vcc is much larger than Vb, this is approximately equal to:

This is how long stage 2 will last. Similarly, stage 1 will last for approximately

Therefore, a full cycle will take

before the next cycle begins. The frequency of the wave is thus:

Viola! We are done!

With the given values in the first schematic (C1=C2=1uF, R2=R3=100K), the frequency is roughly 6.5Hz. These symmetric values can produce a square wave of 50% duty cycle. But they do not have to be symmetric. By using different R2 and R3 (or different C1 and C2), you can easily create waves with any desired duty cycle.

Practice

It’s very easy to prototype the circuit on a breadboard. Here is an example:

Connecting an oscilloscope to output O2, the result shows a decent square wave with 50% duty cycle at about 6.7Hz. Looks quite nice.

I also checked the signal on T2’s base pin. The result is on the left. As you can see, the beginning of stage 2 is signaled by the jump to a large negative value. During this stage, C1 charges through R2, so T2’s base voltage rises continuously. As soon as it crosses Vb, T2 conducts, and its base remains at Vb until the start of the next cycle.

Next, let’s blink some LEDs with the oscillator. You can either connect LEDs in series with R1 and R4, or directly to output O1 and O2. Check the video below (the circuit below uses C1=C2=10uF):

Finally, if you want, you can make a printed circuit board, so you can carry it around, or use it to decorate a toy with flashing LEDs. Enjoy!

Appendix

Frequency change when connecting LEDs with R1 and R4 in series
As mentioned above, one way to connect LEDs into the multivibrator is by putting them in series with R1 and R4. One interesting thing I noticed is that when doing so the frequency of the LED blinking is much faster than the calculated frequency. So what’s happening? A careful analysis reveals that this is not surprising. The main reason is that because the LED will drop about Vled=2V, C1 and C2 will not be charged all the way to Vcc-Vb anymore. Instead, they are charged to about Vcc-Vb-Vled. Consequently, it takes less time for C1 or C2 to charge from a negative voltage to +Vb, hence the oscillation frequency is faster. The precise formula is actually:

Since Vb+Vled is quite significant compared to Vcc, we cannot make the same approximation as above anymore. For example, with the given values in the first schematic (C1=C2=1uF, R2=R3=100K), and assume Vcc=+5V, the frequency is now roughly 10Hz (compared to 6.5Hz when LEDs are not connected). So this explained why the LED blinking speed seems faster than calculated.

30 Responses to “Learning Electronics — 1. Astable Multivibrator”

  1. [...] transgression, but it stems from our discomfort with analog circuits. Luckily, [Ray] published an illustrated guide on building multivibrator circuits. This is a simple method of assembling a two-output oscillator. All it takes is a pair of NPN [...]

  2. Chris Hunt says:

    Great post! I’m looking forward to seeing more like this.

  3. Harald says:

    Note that if Vpower is reaches or exceeds approx. 9 V an additional diode in each emitter connection of the NPNs is required to avoid reverse breakdown of the B-E junction which occurs at around that voltage. The reverse breakdown will discharge the capacitors much faaster than calculated thus raising the frequency of the oscillator.

    Regards,
    Harald

  4. [...] transgression, but it stems from our discomfort with analog circuits. Luckily, [Ray] published an illustrated guide on building multivibrator circuits. This is a simple method of assembling a two-output oscillator. All it takes is a pair of NPN [...]

  5. Aaron says:

    In your circuit you show polarized capacitors and have them charging to a negative voltage (albiet only 0.7v and for quite a short time). Would this not shorten the life of the capacitors or does it really make no difference at this voltage? My understanding is that you should use unpolarized in an application like this.

    This is an excellent article. I am looking forward to seeing the rest.

    • ray says:

      I don’t think it makes any difference in terms of the capacitor life. In any case, this is a fairly standard circuit, I am sure someone has tested it for reliability.

  6. Jonathan says:

    This is a great find. Good Work.

  7. Miroslav says:

    Hi. There is a problem with your circuit: base current is barely enough to saturate the transistors. With your current setup, Rb/Rc=100, so transistor must have a current gain of at least 100. This is not always true, even for small signal transistors like 2N3904. With high power transistors (less current gain) the circuit will certainly fail to oscillate.

  8. Urb Anwriter says:

    Pardon my ignorance – the mathematically ‘never saw the point’ crowd – but in the appendix portion of the article do I see a clue to why multivibrator circuits driving LEDs increase the flash rate (albeit with vastly reduced brightness) as I decrease the supply voltage? Now I can see why I’ll have to take a refresher math course – then I’ll be able to forecast the flash rate of my own circuits. : )

    Thanks for a well done article – one that I am positive will reward re-reading.

    • ray says:

      Yup, that’s correct. The function plot below shows the frequency (1/t, and leaving out the RC constant) with respect to the supply voltage (Vcc):
      1/t function plot
      As you can see, the lower the supply voltage, the higher the frequency.

    • ray says:

      Note that if LEDs are not connected in series, the relationship between frequency and voltage will actually reverse: that is, frequency increases as supply voltage increases. This can be seen clearly in the plot below:
      1/t function plot (no LED)
      This means the voltage drop on the LEDs not only causes the frequency to be higher, but also causes the relationship between frequency and Vcc to flip. Interesting, I’ve never thought about this before.

  9. Sergei says:

    Great post. Could you clarify for me why the capacitors at the end of the cycle have -(Vcc – Vb)? The interaction of the plates is kind of fuzzy for me.

  10. [...] that can be used to flash LEDs, or clock other circuits. You will get an intuition on what causes multivibrator continuously generate. Formulas allow to calculate resistor and capacitor values for particular [...]

  11. jade says:

    Can i use TIP 47-50 transistors, instead of 2N3094? I am so in need of square wave generating circuit using those stuffs. Is it possible? Thankyou!

    • ray says:

      I assume so, but you do have to check the current gain (beta) of the transistor. The higher the better. I would recommend at least 100 or higher.

  12. Alla Sh says:

    Thank you so much for this! finally found good explanation :)

  13. André Plante says:

    Thanks a lot for this great explanation, I liked the text and the maths. It is the best I’ve fund on the web yet. Keep the good work!

  14. mackay says:

    Very nice… I’m an amateur.. I’d like to do the same thing with PNP transistors and create a circuit with one LED that turns on for like 15-20 seconds and then stays on for like an hour (adjusting R1C1 and R2C2 to achieve it..

    can you help?

    Thanks,

    -MaTT

    • ray says:

      An hour long delay will require a large capacitor. You may want to use a microcontroller instead, which will allow you to set precise timing of any length.

      • Mackay says:

        Thanks for your reply. Can’t use a microprocessor in this case.. too much power and bulk. If I use a large resistor on a medium capacitor I might be able to get close to an hour… but.. honestly, I don’t know if that’s a power drain or not.

        What about a 555 timer?

        Thanks

        • ray says:

          Microcontrollers like ATtiny45 (in 8 pin package) are no larger than the size of 2 transistors, and in sleep mode they consume almost no power. They are cheap, require no extra components to operate (most of them have built-in oscillators), and you can programmably set any delay time you want without resorting to large capacitors. If size is a major concern, you can use SMT package. So I would suggest you think twice before ruling out microcontrollers.

          555 also works, there are plenty of example circuits using 555 you can find online. In any case, I think if the primary purpose is to get the work done, microcontrollers are the way to go; if the primary purpose is to learn and build things from scratch, I am all for using discrete components.

  15. Joris says:

    I have tried to make this circuit but when measuring the output voltage I found that it rose slowly to the supply voltage (5V), stayed there for a while, fell quickly to 0V and immediately started rising againg to 5V, fell to 0V again and continued this cycle. This is obviously not a square wave, but I don’t know what the problem is. I used bc170b as resistors and the capacitors I can use are 1000 microfarad and 100 microfarad. What range of resistors should I use to get a proper square wave? The frequency doesn’t matter as long as it’s not much less than 1 Hertz. I want to use it as clock input for cmos ic’s.

  16. Alemayehu fentie says:

    What is the main thing to replace(chang)the transistor?is that hfe is enough? I want to your help.

  17. ladiel says:

    pls ray. I luv ur article but how did the v(t) change to vcc-v(t)

  18. I couldn’t resist commenting. Well written!

Leave a Reply