Feed on
Posts
Comments

OpenSprinkler v2.1u Build Instructions

(Note: all images below are ‘clickable’, in order for you to see the full-resolution details. )



To Begin: Parts Check
osdiy_header
IMG_3731
OpenSprinkler v2.1u kit includes a semi-assembled circuit board, through-hole components, LCD, and injection-molded plastic enclosure..

If you are new to soldering, please take a look at the Preparation page. The most important tool is a good and hot soldering iron: it should provide high temperature to melt and reflow solder. Cold soldering iron is a major source of soldering failure.

Warning: electronic components are small and easy to lose. Before soldering, carefully place the components in a box or container. Small components may get stuck in the plastic bag. DO NOT throw away the plastic bag until you are done with soldering.

Additionally, you need a sprinkler valve transformer (rated 24∼28V AC) and one or more sprinkler valves. These are not included in the kit. You need to purchase them separately. If you have a sprinkler or irrigation system set up, you should have these parts already installed; if not, you can purchase them online or at local retail stores. They are available in many brands (Orbit, Hunter, Rainbird…) and a variety of places (Lowes, Home Depot, Amazon…). Check the F.A.Q. page for some additional information.
To give you a heads up, here are two high resolution images of the assembled board (front and back). Click the images to see them in full resolution.

[Note: due to minor changes in different batches, some components on your board such as relay, RTC, battery holder may differ from the images below].

IMG_3758IMG_3759

Part 1: Soldering
IMG_3730 To begin, place the PCB onto a a vise, and turn on the soldering iron. (If possible, use a fume extractor to help remove solder fumes).

Remember: all images are ‘clickable’.

IMG_3732
IMG_3733a
IMG_3734
Start with crystals X0 (12MHz) and X1 (25MHz). The two crystals have exactly the same shape, so you must read the label on the components to tell them apart. Check the images on the left to see where they are located. It’s important you don’t mix them up, otherwise the controller will not work. Crystals are non-polar, so it doesn’t matter which orientation you insert them.

IMG_0003[Note: if your board comes with DS1307 RTC, you will find an additional crystal X2 (32.768kHz)– it’s cylindrical and very small (see picture on the right). Make sure to solder this crystal as well. If your board comes with DS3231 RTC, you won’t see X2 as it’s built-in to DS3231].

To solder, insert the components through the PCB holes. To increase productivity, I usually insert multiple components, and use painter’s tape to fix them in place (see image on the left). You can use as many pieces of tapes as you need. Then flip the PCB and solder all leads. This way you can solder multiple components at once.

Make sure your soldering iron is hot, and can easily melt and reflow solder. After soldering, use a diagonal cutter to clip the excessive leads.

IMG_3735IMG_3736

IMG_3737a
IMG_3738a
Next, now solder C1, a 100uF electrolytic capacitor. Electrolytic capacitors are polarized: make sure the longer (positive) lead goes into the hole marked with +. To double check, there is a white stripe on the capacitor body which points to the negative lead.

Continue to solder C2 (100uF, same as C1), and C3 (220uF, smaller). Again, make sure the longer lead goes to the hole marked +.

Next, solder the two IC sockets (40-pin and 28-pin). Before inserting the IC sockets to the PCB, check to make sure all pins are straight. Every socket has a small notch (see the picture below) to help identify the orientation. This notch should match up with the silkscreen on the PCB. After insertion, double check and make sure no pin is left out or twisted. The solder joints should be clean and free of any solder bridge.

IMG_3739

IMG_3740 Now solder the fuse — bend one pin down and seat it vertically on the PCB. Then solder the two leads and clip. The fuse is non-polar.
IMG_3741a
IMG_3742a
Moving on, now you will solder a bunch of peripheral components: power switch, USB connector, 24VAC terminal block (orange color, 4mm spacing), three push-buttons, RJ45 Ethernet Jack, and the 2×4 expansion board pin headers.

Also solder the 10 metal oxide varistors (MOVs). Each MOV is a blue, disc-shaped component. It’s non-polar, and its main purpose is to absorb transient high voltage and protect the circuit from power surge.
IMG_0004
[Note: if your board has no MOV slot above the rain sensor terminal, you can solder the MOV directly onto the two pins of the rain sensor terminal. See picture on the right].

Next, solder the eight triacs T1-T8 (MAC97). Each triac is shaped like a half cylinder. Orient it such that the half cylinder matches the PCB silkscreen (i.e. the flat side should face the fuse and orange terminal block). Use your hand to bend the middle pin slightly backward, so that you can easily insert it to the PCB holes.

IMG_3743a
IMG_3744a
Solder the relay and the 1×16 LCD female pin header.

[Note: some kits may come with yellow-colored relays].

It’s important that the pin header is seated tight on the PCB. Try to avoid any gap between the pin header and the PCB, otherwise it will be difficult to put the cover on later.

Now take out the LCD and the 1×16 male header. Solder the male header onto the LCD. The easiest way to do so is by making use of a breadboard to hold the pin header during soldering. Again, it’s important that the pin header is seated tightly to the LCD’s PCB.
IMG_3745
IMG_3746
IMG_3747
Now flip the PCB and solder the 12mm battery holder. [Note: if the battery holder is on the front side and pre-soldered for you, you can proceed to the next paragraph]. To begin, use a small amount of solder to tin the PCB pad. Then place the battery holder down and make sure the orientation matches the silkscreen (rectangular and circular parts). Solder one pad first, and then the other pad. Make sure both solder joints are reliable.

After the battery holder is soldered on, take out the CR1220 battery, and snap it into the holder. The flat side (marked by +) should face up. The easiest way is to first insert the battery towards the side with a straight metal piece, then press the battery firmly to snap it in. If you ever need to take the battery out, push the straight metal piece as much as you can, until the battery pops out.

IMG_3748IMG_3749

IMG_3750
IMG_3751
Finally, solder the remaining two 2p terminal blocks and one 8p terminal block. These terminal blocks have green color and 5.08 pin spacing.

VoilĂ , you are all set with soldering! Carefully check your board with the image below. At this point, DO NOT pop in the two ICs yet (even though the image shows they are inserted).

IMG_3758

Part 2: Testing
IMG_3752
IMG_3755
In this section, you will test the circuit and make sure it functions. If you’ve already inserted the two ICs, take them out for now.

First, measure the resistance between VIN (+5V) and GND as well as between VCC and GND. These pins can be located in the pinout area above the LCD headers. The resistance should be at least several kilo-ohms. If either resistance is below one kilo-ohm, there is probably a shorting or solder bridge somewhere.

Next, take out the orange terminal block, wire in 24VAC power, and insert it to the 24VAC port on the left side of the circuit board. Slide down the power switch to turn it on. Measure the voltage between VIN and GND — it should be around 5V; also measure the voltage between VCC and GND — it should be around 3.3V.

Important: if anything burns or smokes, immediately turn off power. Check to see if there is any component visibly damaged. If you can’t figure out the problem, post a message in the forum and we will help you.

IMG_3756 Once the voltage checking is passed, you can unplug the power, and go ahead to pop in the two ICs — ATmega644 microcontroller, and ENC28J60 Ethernet controller. To insert an IC, bend its pins slightly inward on a hard flat surface. While inserting, make sure no pins are left out or twisted. Make sure that its notch matches the notch on the IC socket. If you’ve done it right, the notch on ATmega644 should face left, and the notch on ENC28J60 should face up.
IMG_3754
IMG_3753a
Now install the LCD. Start by using the M3 (3mm) screws to fix the two copper support pillars to the PCB. Then insert the LCD to the female pin headers, and finally use the other two M3 screws to tighten the LCD to the support pillars.
IMG_3760 Now you can power on the controller and check its firmware features. You can either plug in 24VAC, or use a USB cable to power the controller (DO NOT have both sources on at the same time). We strongly recommend using USB to power the board and test software features first (see picture on the left). This won’t activate any sprinkler valves, but allows you to check firmware features and set IP address etc. The USB connector can also be used to power an external WiFi adapter, and used for flashing new firmware.

Part 3: Enclosure
IMG_3762

IMG_3763

OpenSprinkler v2.1u comes with an injection-molded enclosure. To install the enclosure, place the circuit board on the enclosure’s bottom piece, then cover it with the top piece. Flip the assembly upside down, and install the four screws. The screws are relatively big, and require a considerable amount of force to screw them in. It’s recommended that you use a electric screw driver to make it easy for you.

That’s all. Now you have a functioning OpenSprinkler. Congratulations, and hope you enjoy using it!

8 Responses to “OpenSprinkler v2.1u Build Instructions”

  1. Hey Ray . . .
    Thanks for such a well made unit with clear instructions. Works like a charm.
    My board looked like this:
    http://wwwphoto.org/2014/05-May/20140520-OpenSprinkler_9046.jpg

    Looking forward to trying your other products.

    Jim

  2. Christos Keleshis says:

    Thanks for such a nice device and the great instructions to build it.
    Quick Question:

    When powered by the USB cable and i try to use the power switch it does not turn it Off. Despite its positions its always on On power state. Is this normal?

    Thank you,

    Christos

  3. ned says:

    I bought one recently that comes with the following versions board 2.1 and firmware 205.
    When the power is turned on, a lot of time the board does not power up until the reset button (below LCD) is toggled.
    I also can’t go to the setup menu by pressing B3 and powering up the board.
    Holding B3 and the reset button gets me to the setup menu navigation.
    However, flipping through the menu does not always work and a lot of time the board stalled and power restart is required.

    When the board is on (LCD on) through the help of Reset button, it comes up as DISABLED.

    Any idea on what may be wrong?
    The check procedure mentioned in this page has been followed and passed.

    Thanks

    • ray says:

      Two quick comments:
      1. Does it appear the same when you power the controller with USB, or power it with 24V AC? This can help which power section is causing the issue.
      2. Using a multimeter, measure the voltage between VIN-GND, when the issue occurs, does the voltage drop significantly? Do the same checking on VCC-GND, and let me know your findings.

      • ned says:

        1. Yes. It does not matter which power source I use.
        2. VIN-GND is at 5V and VCC-GDN is at 3.3V

        I have videos during the measurement. I will email them to you.

    • ray says:

      OK, since this is the DIY kit, I will need you to send me high resolution pictures of the front (without LCD) and back of the PCB, under good lighting condition, so I can check if there is any soldering related issue.

  4. ned says:

    1. Yes, with either one of them power supply, the board reacts the same way
    2. VIN-GND: 5V
    VCC-GND: 3.3V

    I have sent email to support for details and video links.

    Thanks

Leave a Reply to Christos Keleshis